- 您现在的位置：买卖IC网 > Sheet目录1216 > FTDI USB-KEY (FTDI, Future Technology Devices International Ltd)MOD USB SECURITY KEY DEVICE
Document Reference No.: FT_000062
USB-Key Datasheet Version 1.00
Clearance No.: FTDI# 41
Appendix A – FTDI USB Key FT232R EEPROM Configuration
This FT232R device within the FTDI_USB_KEY contains an EEPROM which contains the USB configuration
descriptors for that device. When the FTDI_USB_KEY is plugged into a PC or a USB reset is performed, the
PC will read these descriptors. The default values stored into the internal EEPROM are defined in Table 5.1
Parameter
USB Vendor ID (VID)
USB Product UD (PID)
Serial Number Enabled?
Serial Number
Pull down I/O Pins in USB
Suspend
Manufacturer Name
Product Description
Max Bus Power Current
Power Source
Device Type
USB Version
Remote Wake Up
High Current I/Os
Load VCP Driver
Invert TXD
Invert RXD
Invert RTS#
Invert CTS#
Value
0403h
6001h
Yes
See Note
Disabled
FTDI
FTDI USB-KEY
90mA
Bus Powered
FT232R
0200
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Disabled
Notes
FTDI default VID (hex)
FTDI default PID (hex)
A unique serial number is generated and programmed into the
EEPROM during device final test.
Enabling this option will make the device pull down on the UART
interface lines when the power is shut off (PWREN# is high).
Returns USB 2.0 device description to the host.
Note: The device is be a USB 2.0 Full Speed device (12Mb/s) as
opposed to a USB 2.0 High Speed device (480Mb/s).
Taking RI# low will wake up the USB host controller from
suspend.
Enables the high drive level on the UART and CBUS I/O pins.
Makes the device load the VCP driver interface for the device.
Signal on this pin becomes TXD# if enable.
Signal on this pin becomes RXD# if enable.
Signal on this pin becomes RTS if enable.
Signal on this pin becomes CTS if enable.
Table 5.1 Default Internal EEPROM Configuration
The internal EEPROM in the FT232R can be re-programmed over USB using the utility program MPROG.
MPROG can be downloaded from the www.ftdichip.com . Version 2.8a or later is required for the FT232R
chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their
design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service.
Copyright ? Future Technology Devices International Limited
8
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
FTS125-COO-010.0M EVAL KIT
GPS TIMING MODULE EVAL BOARD
FWA-4000AH
FUSE 4000A 130V UL
FWH-6.30A6F
FUSE 6.30A 500V HS FERRULE
FWH-900A
FUSE 900A 500V HIGH SPEED
FWJ-400A
FUSE 400A 1000V
FWK-60A25F
FUSE 60A 750V 25X146MM FERRULE
FWP-50A14F
FUSE 50A 700V HS FERRULE
FWX-50A14F
FUSE 50A 250V FERRULE UL
相关代理商/技术参数
FTDNS4X4BL
制造商:Panduit Corp 功能描述:Fitting That Transitions From Various 4X4 Systems To 4X4 Fiber-Duct System 制造商:Panduit Corp 功能描述:FITTING, ADAPTER FROM 4" X 4" FIBER-DUCT - Bag 制造商:Panduit Corp 功能描述:FITTING, ADAPTER FROM 4 X 4 FIBER-DUCT
FTDNS4X4LG
功能描述:电线导管 Fitting, Adapter from 4" x 4" Fiber-Duct RoHS:否 制造商:Panduit 类型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 颜色:Light Gray 大小: 最大光束直径: 抗拉强度: 外部导管宽度:25 mm 外部导管高度:25 mm
FTDNS4X4OR
功能描述:电线导管 Fitting, Adapter from 4" x 4" Fiber-Duct RoHS:否 制造商:Panduit 类型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 颜色:Light Gray 大小: 最大光束直径: 抗拉强度: 外部导管宽度:25 mm 外部导管高度:25 mm
FTDNS4X4YL
功能描述:电线导管 Fitting, Adapter from 4" x 4" Fiber-Duct RoHS:否 制造商:Panduit 类型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 颜色:Light Gray 大小: 最大光束直径: 抗拉强度: 外部导管宽度:25 mm 外部导管高度:25 mm
FTDR8D107-20
制造商:INCON 功能描述:
FTE 650W 230V
制造商:Hawco 功能描述:60X245MM 650W/240V CER H
FTE01
制造商:OTAX Corporation 功能描述:
FTE09
制造商:TE Connectivity 功能描述:SWITCH SPDT CTR OFF